ClearCom KB-212 Manual de Instruções

RS-601BELTPACKINSTRUCTION MANUAL

6 R S - 601 B ELTP A CKCONTROLS AND ADJUSTMENTS Figure 1: Control Panel of an RS-601 Beltpack Talk Button To talk on

7R S - 6 0 1 B E L T P A C K release the button, your voice no longer transmits to the intercom line. To “latch” the

8 R S - 601 B ELTP A CK Call ButtonWhen you press the call button, a call signal is sent to all other stations on the

9R S - 6 0 1 B E L T P A C K Power Status Light An illuminated power status light indicates that the beltpack is co

1 0 R S - 601 B ELTP A CKOnce setup mode is active, if you do not select or program a feature within five seconds, t

11R S - 6 0 1 B E L T P A C K Figure 3: Pinouts of RS-601 Computer ConnectorFigure 4: Back of RS-601BeltpackPIN FUNC

1 2 R S - 601 B ELTP A CK Sidetone Adjustment To adjust the beltpack’s “sidetone,” or the level of one’s own voice in

13R S - 6 0 1 B E L T P A C K CONNECTING YOUR BELTPACK An RS-601 beltpack works with all previous versions of Clear

1 4 R S - 601 B ELTP A CKThe RS-601 is not recommended for use with RTS-TW systems as the frequency response curves a

15R S - 6 0 1 B E L T P A C K Auxiliary (“AUX”) Headphone Clear-Com designed the auxiliary headset connector, label

RS-601 Instruction Manual ©2005 Vitec Group Communications All Rights ReservedPart Number 810287, Rev. B Vitec Group Communicatons Inc. 4065 Hollis S

1 6 R S - 601 B ELTP A CK Headset Connector You connect a headset to the beltpack at the 4-pin male XLR connector lab

19RS-601 BELTPACK CUSTOMIZING YOUR BELTPACK You can customize an RS-600 series beltpack for quick adaptation to the needs of any working environment.

20RS-601 BELTPACKthe same settings. And V-Pack includes many more features you can program for your beltpack. To operate the V-Pack software, you must

21RS-601 BELTPACK SETTINGS YOU CAN CUSTOMIZE Table 1 shows the beltpack functions you can customize with onboard controls. Note than each function i

22RS-601 BELTPACKMode Select, Function 1 A “mode” is one complete “package” of settings for a beltpack. Each beltpack’s memory holds four modes. You c

23RS-601 BELTPACK Latch Disable, Function 2A beltpack’s talk button normally latches when you tap it twice. If you select to disable this function, th

24RS-601 BELTPACKTalk Disable, Function 3 This function turns the talk button on or off. When off, the talk button does not function. Turn the talk bu

25RS-601 BELTPACK Call-on-Talk, Function 4 This function causes a beltpack to send a call signal each time you press or latch the talk button. You can

26RS-601 BELTPACKElectret Microphone, Function 5This function allows a beltpack to operate with an electret-microphone equipped headset. It only affec

27RS-601 BELTPACK Call Signal Tone (in Earphone), Function 6 When this function is on, the beltpack produces an audible call signal in the headset wh

RS-601 BELTPACK 1CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . .1QUICK START . . . . . .

28RS-601 BELTPACKElectret Microphone, Hi-Lo, Function 7 This function selects high or low gain for an electret microphone. The “on” setting selects hi

29RS-601 BELTPACK Lockout, Function L “Lockout” allows you to prevent all editing of beltpack functions with onboard controls. When you select “lockou

30RS-601 BELTPACKRESTORING THE FACTORY DEFAULT SETTINGSTo restore the factory default settings for all four modes: 1. Press and hold the setup button

RS-601 BELTPACK 31SPECIFICATIONS0 dBv is referenced to 0.775 V RMS General Amplifier Design: I.C. amplifiers, including s

32 RS-601 BELTPACKHeadphone AmplifierLoad Impedance: 50 - 2,000 ohmsOutput Level: +17 dBv before clippingDistortion: <

RS-601 BELTPACK 33Dimensions 4.58"H x 3.73"W x 1.34"D (116 x 95 x 34 mm)Weight 7.3 oz. (0.20 kg)Specificat

34 RS-601 BELTPACK

RS-601 BELPACK 35MAINTENANCE GENERAL USAGE NOTES Cabling choices can greatly impact the performance of an intercom system. Length, gauge, and shiel

RS-601 BELPACK 36To rotate the beltclip to a new position: 1. Remove the setup help label and the two retaining screws. 2. Rotate the beltclip 90o or

RS-601 BELPACK 37PROBLEMCall light stays on. CAUSE DC voltage present on audio line pin 3. SOLUTIONCheck cables for shorts and cross-wiring. Make sur

2 RS-601 BELTPACK SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 31MAINTENANCE . . . . . . . . .

RS-601 BELPACK 38PROBLEMCan’t change configuration on beltpack. CAUSE Disabled access to functions. SOLUTIONRestore access by resetting to factory def

RS-601 BELTPACK 39WARRANTY Vitec Group Communications (VGC) guarantees this product to be free of manufacturing defects in

40 RS-601 BELTPACKWeb site: www.clearcom.com (Click the 24 X 7 User Support symbol on the Web site.) For technical support

RS-601 BELTPACK 41terms of the warranty, the normal procedure will be to repair or replace any defective Line Replaceable

42 RS-601 BELTPACKREPLACEMENT UNITSShould VGC determine, in its reasonable discretion, that any part of a product is defec

RS-601 BELTPACK 43respect to any non-conformance or defect in any such product and/or part thereof delivered hereunder, or

44 RS-601 BELTPACK(But you must have your PIN number ready)Web site: www.clearcom.com (Click the 24 X 7 User Support symbo

RS-601 BELTPACK 1INTRODUCTIONThank you for choosing this product. Clear-Com designed the 600 series of beltpacks to me

2 RS-601 BELTPACK The RS-601 offers all the performance and durability of Clear-Com’s world-standard beltpacks, plus TW

RS-601 BELTPACK 3QUICK STARTTo start using your beltpack immediately: 1. Connect the appropriate line cables (3-pin XLR) from an active intercom line

RS-601 BELTPACK4

5R S - 6 0 1 B E L T P A C K OPERATING YOUR BELTPACK An RS-601 beltpack works with all previous versions of Clear-C